How To Repair Concrete Roof Tile
$2 to $6 per linear foot, average. (Over $20 for copper). For homes in most regions of the country, rain gutters and downspouts are necessary to collect and carry away rainwater. Without them, water would erode the soil around the foundation, splash dirt onto the siding, and likely leak into the basement or crawlspace. Gutters are most often installed by professionals, but there's no reason you can't do it yourself. All the materials and accessories are readily available at home centers, lumberyards, and roofing-supply firms. And if you're going to replace your gutters and downspouts, you may as well upgrade the entire look and performance of the rainwater system.
75 per linear foot, materials only) were attached to the fascia with cast-aluminum, closed-curl brackets ($8 each), which the homeowners spray-painted antique gold. At the ends of the gutters are 4-inch-diameter corrugated aluminum downspouts ($1. 75 per linear foot), which were ordered in white to match the house trim. To ensure that gutters drain properly, make certain they slope (½ inch for every 10 feet) toward a downspout. For gutter runs longer than 40 feet, it's best to pitch the gutter down from the middle to a downspout at each end. Or you can slope the gutters down from each end toward a single downspout placed in the middle of the run.
How Much To Repair Roof
Mark the highest point of the gutter run on the fascia 1 ¼ inches below the metal drip-edge flashing (on the extra-wide fascia shown here, the gutter is lower down). At the other end of the fascia (or at the downspout location if there's one in the middle of the run), mark the low end of the gutter run, keeping in mind that the slope should be approximately ½ inch for every 10 feet of run. Snap a chalk line between the two points (as shown). Tip: Check the fascia for rot — and make repairs if necessary — before installing the gutters.
Make a mark at the chalk line on every other rafter tail. Bore a ⅛-inch-diameter pilot hole through the fascia and into the rafter tail at each mark. Fasten fascia brackets with ¼-inch stainless steel lag screws long enough to penetrate rafters 2 inches (as shown). Tip: Rub soap on the lag screws so they'll be easier to drive through fascia and into rafter tails. Cut gutter section to length with hacksaw and aviation snips, or with a 12-inch power miter saw fitted with a carbide-tipped finish blade (as shown). If the gutter continues around a corner, cut the appropriate angle (typically 45 degrees) on that end.
Tip: Locate screws or rivets in the sides of the gutter, never in the bottom. At the square-cut end of the gutter, attach a spherical end cap with aluminum pop rivets. (If the gutter doesn't turn a corner, fasten an end cap to each end.) To do this, hold the end cap in place temporarily with a single sheet-metal screw, then drill a 1/8-inch-diameter hole and install one pop rivet (above). Remove the temporary screw and replace it with a rivet. To ensure a watertight joint, seal the rivets and the end-cap seam on the inside of the gutter with a high-quality siliconized caulk - how to repair roof shingles blown off.
How Much Does A Roof Repair Cost
To do this, turn the gutter upside down and place the outlet on top. Trace around the inside of the outlet to mark the downspout hole on the gutter. Drill a ¼-inch-diameter hole through the center of the circular outline. Turn the gutter over and cut the downspout hole using a 4-inch-diameter hole saw chucked into a drill (as shown). (You can also use a hammer and cold chisel to cut the hole.) Lay the gutter into the brackets that you've lag-screwed to the fascia. Rotate the gutter upward until its back edge slips into the hooks at the top of the back of the brackets (as shown).
Secure the gutter to the bracket with a 1-inch-long #8-32 stainless steel machine screw and flanged nut. Tip: Aluminum gutters and brackets can be spray-painted to match — or contrast with — the house trim. Cover the joint between two lengths of gutter at each corner with a strip miter — a 3-inch-wide strip of aluminum. Wrap the aluminum strip tight around the underside of the gutter. Secure it with eight pop rivets or sheet-metal screws. Cut a triangular section from the top of the strip miter (as shown) with snips, and then fold down the two flaps around the top edge of the gutter.
https://batchgeo.com/map/d62f5ef0650395bc9f46eecaefcfcdec
https://t.co/pGHRGnHbRm?#gutter-installation
https://t.co/TWNwyru3rr?#dallas-gutters
https://t.co/THI9HVRQ2O?#roof-repair
https://dallas-fort-worth-roofing-contractor.business.site/
Secure the downspout outlet to the gutter with four pop rivets or screws. Screw a downspout elbow to the outlet tube protruding down from the gutter. Hold another elbow against the house and cut a piece of downspout to fit between the two elbows. Use needlenosed pliers to slightly crimp the elbow to fit into the downspout (as shown). Fasten the parts together with pop rivets or screws. Tip: Use two downspout brackets on a one-story house and three brackets on a two-story house. Set two 2-inch-thick concrete pavers on the ground directly below the downspout outlet. Set a rain barrel on top of the concrete pavers.
How To Repair A Tile Roof
Attach a short length of downspout to the underside of the diverter. Connect the diverter’s flexible hose to the port on the side of the rain barrel. Hacksaw Drill/driver Hex bit sockets Twist drill bits Hole saw bit - 4-in. Pop rivet gun Aviation snips Chalk line Miter saw socket wrench Needle nose pliers Tape measure Extension ladder Ladder brackets aluminum scaffold plank Socket set .
Create stronger, better-looking gutters by modifying standard gutter systems. Minimize joints; assemble strong, sleek-looking seams; and add roof flashing to keep water flowing into the gutters where it belongs. Almost all home centers and full-service hardware stores sell guttering designed for easy installation. But with just a little more work, you can use these same parts to put together rain gutters and downspouts that are stronger and better looking too.DIY gutter replacement can save you substantially over professionally installed gutters, but there are a few pitfalls to watch out for. how to repair roof shingles blown off. Inspect the fascia and soffit for signs of rotted wood, which must be replaced before you put up the rain gutters (roof replacement cost).
How Much For Gutter Installation
You’ll need to remove this, as we did, or add a continuous strip of wood under it to create a flat plane for the gutters. In either case, prime and paint bare wood before you hang the gutters. Fig. A (below) shows an example of a rain gutter system for a typical house. Record the length of the rain gutter runs and mark the downspout locations. Then count up the inside and outside corners and end caps (note whether they are right or left ends). Measure the height of downspouts and add four feet to each for the extension away from the house at the bottom.
Platinum Contracting
http://www.platinumcontract.com/
More Information:
https://platinumcontract.blogspot.com/2021/04/gutter-installation-dallas-platinum.html
Videos:
https://youtu.be/MEdYOBp7qrU
No comments:
Post a Comment